STANDARD FEATURES QJ241 JAW CRUSHER ENGINEERING IN MOTION QJ241 JAW CRUSHER KEY SPECIFICATIONS DATA Equipment Single toggle C10 jaw crusher Feed opening 1000 mm x 650 mm / 40" x 26" Optimum feed size 520 mm3 / 21 inch3 Engine C7.1 Acert 168 kW / 225 hp Transport dimensions 13.90 m / 45' 7 ⅜" (l) 2.64 m / 8' 7 ⅞" (w) 3.22 m / 10 ...

The jaw crusher discharge opening is the distance from the valley between corrugations on one jaw to the top of the mating corrugation on the other jaw. The crusher discharge opening governs the size of finished material produced by the crusher. Measuring Discharge Opening: Measure distance at bottom of jaws at the point of the crushing cycle when the bottom of jaws is closest together.

24 x 36 in Lippmann jaw crusher - 24 x 36 inch feed cavity - 32,000 lbs total weight - Removed in good working condition - Inspected and refurbished with parts repaired and replaced as needed - 150 HP 890 RPM induction motor - Flywheel RPM: 275...

Jaw Crushers ... Burbank Abrasion Test — A standard method of comparing the relative abrasiveness of rocks, minerals and ores. Cage — A screening device, fixed or adjustable, made of precisely spaced bars or slotted plate, where final sizing is accomplished within the crusher.

The gyratory crusher can, just like a jaw crusher, accept boulder sizes close to 1.5 m (for the largest equipment). – This crusher can handle products with a Mohs hardness that is not necessarily less than 5. – As is the case for jaw crushers, there is not any mutual sliding on grinding surfaces, but simply rolling of the nut on concaves.

group, has installed over 10 000 jaw crushers since the 1920s. Today the C Series is indisputably the world's favourite jaw crusher. Where cost-efficient primary reduc-tion of hard, abrasive materials is concerned, C Series crushers represent the highest tech-nical and manufacturing knowledge. All C Series jaw crushers are based on a

Average throughput rate of single-toggle jaw crusher, standard version, tolerance ± 10% Double-toggle jaw crushers Design Double-toggle jaw crushers are equipped with a double-toggle system, which is con - trolled by a pitman that moves up and down under the influence of an eccentric shaft, causing the toggle plates to alternately flex and ...

jaw crusher good standard. jaw crusher good standard GM stone crusher machine is designed to achieve maximum productivity and high reduction ratio. From large primary jaw crusher and impact crusher to cone crusher and VSI series for secondary or tertiary stone crushing, GM can supply the right crusher as well as complete crushing plant to meet ...

optimum performance, the jaw crusher needs to have a good feed level and a homogeneous feed. Our jaw crushers are of the single-toggle type and feature a deep, symmetrical crushing chamber, a large feed opening for its size, and an ideal nip angle that offers smooth material flow and high reduction efficiency. Jaw crushers are normally capable ...

The correct nip angle between the movable and fixed jaw dies ensures good bite and material flow down, even with slippery feed material. It also reduces wear on the jaw dies, reducing operating costs. With a good grip, the jaw crusher can crush rocks efficiently through the entirety of the cavity, and the nip angle can be further improved with

Standard fit on all Jaw & Cone crushers. A good all round liner for all applications. 22% MANGANESE Optional fit for all Jaw & Cone crushers. Work hardens quicker in abrasive applications. 14% MANGANESE This is an option that & available if required although not generally stocked. For use in soft low abrasion applications. MANGANESE IS ADDED TO ...

It must be at least 36 in. wide for an 18 x 36 jaw crusher. So a 4-ft by 8-ft screen would be acceptable. The 1-in. screen is a second deck for the 38 tph from the jaw crusher, so the deck correction factor is 0.90 and that screen capacity is 2.1 x 0.9 = 1.89 tph/sq ft. The screen area needed under the jaw crusher is 38/1.89 = 20.1 sq ft.

The gyratory crusher can, just like a jaw crusher, accept boulder sizes close to 1.5 m (for the largest equipment). – This crusher can handle products with a Mohs hardness that is not necessarily less than 5. – As is the case for jaw crushers, there is not any mutual sliding on grinding surfaces, but simply rolling of the nut on concaves.

The jaw crusher is a compression type crusher. Feed material is crushed between fixed and mov-able jaw dies. Large particles are ... Standard (XT710) • Good in gravel and non abrasive rock • Tooth spacing ideal for fines removal • Power requirement and crushing stresses are in balance

· Good top size control Austenitic manganese steel is the industry standard material for jaw crusher liners. Due to its ability to work-harden during operation it has proven to be versatile and works well in a majority of applications.